Fire-retardant sealants of Ogneza

Application purpose:

• For stoves and fireplaces
• For sealing joints and crevices of surfaces constantly exposed to high temperatures
• For sealing and fixing refractory bricks

Characteristics:

• when heated to +250°C, it becomes superhard;
• high strength;
• well absorbed;
• can be used with natural stone;
• resistant to temperatures up to +1600°С;
• resistant to open flame;
• good adhesion;
• sealant does not emit vapors;
• does not shrink;
• subsequent staining with organic-based paints is possible;
• resistant to cold (capable of withstanding 3 defrost/defrost cycles);
• environmentally friendly;
• durable.

Installation recommendations:

• the surface before application is cleaned of grease, dust, rust with a lint-free cloth. For cleaning, a solvent is used, the remains of which are then removed with a clean, dry cloth;
• porous surfaces are wetted by water;
• the sealant is applied with a sealant gun or a spatula;
• after 24 hours (sealant hardening time), the surface should be heated to +200°C, and then calcined (temperature +200-250°C) for 30 minutes so that the sealant acquires its refractory properties;
• unhardened sealant is removed with water, hardened - mechanically.

Weight: 310 ml.

Application purpose:

• For sealing expansion joints, ventilation penetrations and steel pipe penetrations

Characteristics:

• color: red/white;
• waterproof;
• highly elastic;
• based on acrylic;
• fire resistance level up to 240 minutes;
• excellent adhesion to base materials;
• wear-resistant;
• weather resistant;
• dries quickly;
• stored at temperatures from +5 to +40°C.

Installation recommendations:

• applied with a spatula, sealant gun, spray;
• the surface is pre-cleaned of dust, dirt, oil and other contaminants;
• the space is filled with sealant with a wet layer thickness of at least 3 mm;
• sealant is best applied in layers.

Weight: 20 kg.

Application purpose:

• For sealing expansion joints, ventilation penetrations and steel pipe penetrations

Characteristics:

• color: red/white;
• waterproof;
• highly elastic;
• based on acrylic;
• fire resistance level up to 240 minutes;
• excellent adhesion to base materials;
• wear-resistant;
• weather resistant;
• dries quickly;
• stored at temperatures from +5 to +40°C.

Installation recommendations:

• applied with a spatula, sealant gun, spray;
• the surface is pre-cleaned of dust, dirt, oil and other contaminants;
• the space is filled with sealant with a wet layer thickness of at least 3 mm;
• sealant is best applied in layers.

Weight: 3 kg.

Application purpose:

• For sealing expansion joints, ventilation penetrations and steel pipe penetrations

Characteristics:

• color: red/white;
• waterproof;
• highly elastic;
• based on acrylic;
• fire resistance level up to 240 minutes;
• excellent adhesion to base materials;
• wear-resistant;
• weather resistant;
• dries quickly;
• stored at temperatures from +5 to +40°C.

Installation recommendations:

• applied with a spatula, sealant gun, spray;
• the surface is pre-cleaned of dust, dirt, oil and other contaminants;
• the space is filled with sealant with a wet layer thickness of at least 3 mm;
• sealant is best applied in layers.

Weight: 310 ml.

Application purpose:

• For sealing expansion joints, ventilation penetrations and steel pipe penetrations

Characteristics:

• color: red/white;
• waterproof;
• highly elastic;
• based on acrylic;
• fire resistance level up to 240 minutes;
• excellent adhesion to base materials;
• wear-resistant;
• weather resistant;
• dries quickly;
• stored at temperatures from +5 to +40°C.

Installation recommendations:

• applied with a spatula, sealant gun, spray;
• the surface is pre-cleaned of dust, dirt, oil and other contaminants;
• the space is filled with sealant with a wet layer thickness of at least 3 mm;
• sealant is best applied in layers.

Weight: 600 ml.

Application purpose:

• For installation of cable penetrations
• For sealing seams
• To give fire resistance to seams (both deformation and structural)

Characteristics:

• profitability;
• there are no Russian analogues;
• high adhesion to many materials (wood, metal, concrete, brick, plastic, etc.);
• environmental safety;
• fast drying;
• weather resistance;
• frost resistance - the sealant can withstand 5 freeze / thaw cycles;
• storage and transportation are possible at temperatures from +5°C to +40°C.

Operating principle:

Under the influence of high temperature (above +200 °C), the fire-fighting mastic swells, which ensures its three-dimensional expansion. This prevents fire and smoke from entering adjacent rooms.

Recommendations for use:

• must be kept at room temperature before use;
• applied with a gun, spatula, brush, etc;
• the surface is pre-cleaned of dirt and dust, if necessary, degreased;
• the entire volume of the seams is filled with sealant. If the thickness of the overlap is more than 100 mm, the cracks and voids are first stuffed with mineral wool, after which they are filled with sealant;
• the seams are leveled with a spatula moistened with water (sealant hardening time 25 minutes);
• drying time is 24 hours with a layer of mastic 3 mm, 8 hours with a layer of 1 mm;
• the service life is at least 10 years.

Weight: 3 kg.

Application purpose:

• For installation of cable penetrations
• For sealing seams
• To give fire resistance to seams (both deformation and structural)

Characteristics:

• profitability;
• there are no Russian analogues;
• high adhesion to many materials (wood, metal, concrete, brick, plastic, etc.);
• environmental safety;
• fast drying;
• weather resistance;
• frost resistance - the sealant can withstand 5 freeze / thaw cycles;
• storage and transportation are possible at temperatures from +5°C to +40°C.

Operating principle:

Under the influence of high temperature (above +200 °C), the fire-fighting mastic swells, which ensures its three-dimensional expansion. This prevents fire and smoke from entering adjacent rooms.

Recommendations for use:

• must be kept at room temperature before use;
• applied with a gun, spatula, brush, etc;
• the surface is pre-cleaned of dirt and dust, if necessary, degreased;
• the entire volume of the seams is filled with sealant. If the thickness of the overlap is more than 100 mm, the cracks and voids are first stuffed with mineral wool, after which they are filled with sealant;
• the seams are leveled with a spatula moistened with water (sealant hardening time 25 minutes);
• drying time is 24 hours with a layer of mastic 3 mm, 8 hours with a layer of 1 mm;
• the service life is at least 10 years.

Weight: 310 ml. 

Application purpose:

• For installation of cable penetrations
• For sealing seams
• To give fire resistance to seams (both deformation and structural)

Characteristics:

• profitability;
• there are no Russian analogues;
• high adhesion to many materials (wood, metal, concrete, brick, plastic, etc.);
• environmental safety;
• fast drying;
• weather resistance;
• frost resistance - the sealant can withstand 5 freeze / thaw cycles;
• storage and transportation are possible at temperatures from +5°C to +40°C.

Operating principle:

Under the influence of high temperature (above +200 °C), the fire-fighting mastic swells, which ensures its three-dimensional expansion. This prevents fire and smoke from entering adjacent rooms.

Recommendations for use:

• must be kept at room temperature before use;
• applied with a gun, spatula, brush, etc;
• the surface is pre-cleaned of dirt and dust, if necessary, degreased;
• the entire volume of the seams is filled with sealant. If the thickness of the overlap is more than 100 mm, the cracks and voids are first stuffed with mineral wool, after which they are filled with sealant;
• the seams are leveled with a spatula moistened with water (sealant hardening time 25 minutes);
• drying time is 24 hours with a layer of mastic 3 mm, 8 hours with a layer of 1 mm;
• the service life is at least 10 years.

Weight: 20 kg.

Application purpose:

• For sealing gaps
• To increase the fire resistance of fire gates, doors, smoke dampers, hatches, fireproof safes, etc

Characteristics:

• there is a self-adhesive layer;
• extension: 900%;
• the fire resistance limit is 240 minutes;
• service life: 25 years (subject to operating conditions).

Principle of operation

When the temperature rises to +150 °C and above, the fire-retardant material from which the tape is made swells, due to which the gaps between the fire door frame and the leaf are filled. This prevents smoke and fire from entering the adjacent room.

Exploitation:

• structures with fire-resistant tape are inspected at least once a year;
• during inspection, it is necessary to make sure that there are no unstuck sections of the tape, as well as mechanical damage to the tape;
• if there are peeled off areas, the surface must be degreased and glued with rubber glue;
• if there is mechanical damage, then it is necessary to remove the damaged area with a construction knife (with an overlap of 2-3 cm), and then stick a new tape without butt gaps.

Installation recommendations:

• installation is carried out at temperatures from -10 to +60 ° C;
• the installation site is pre-cleaned of dust and dirt, degreased;
• there should be no gaps at the joints of the pieces of tape;
• when gluing, the tape is tightly pressed against the surface; for reliability, the butt joints and the ends of the tape can be glued with rubber glue;
• the tape is installed without visible distortions and gaps; it may be necessary to use rags, a White Spirit type degreaser, scissors or a construction knife, a marker, a stepladder.

Size: 1,5*10 mm.

Roll length: 35 m.

Application purpose:

• For sealing gaps
• To increase the fire resistance of fire gates, doors, smoke dampers, hatches, fireproof safes, etc

Characteristics:

• there is a self-adhesive layer;
• extension: 900%;
• the fire resistance limit is 240 minutes;
• service life: 25 years (subject to operating conditions).

Principle of operation

When the temperature rises to +150 °C and above, the fire-retardant material from which the tape is made swells, due to which the gaps between the fire door frame and the leaf are filled. This prevents smoke and fire from entering the adjacent room.

Exploitation:

• structures with fire-resistant tape are inspected at least once a year;
• during inspection, it is necessary to make sure that there are no unstuck sections of the tape, as well as mechanical damage to the tape;
• if there are peeled off areas, the surface must be degreased and glued with rubber glue;
• if there is mechanical damage, then it is necessary to remove the damaged area with a construction knife (with an overlap of 2-3 cm), and then stick a new tape without butt gaps.

Installation recommendations:

• installation is carried out at temperatures from -10 to +60 ° C;
• the installation site is pre-cleaned of dust and dirt, degreased;
• there should be no gaps at the joints of the pieces of tape;
• when gluing, the tape is tightly pressed against the surface; for reliability, the butt joints and the ends of the tape can be glued with rubber glue;
• the tape is installed without visible distortions and gaps; it may be necessary to use rags, a White Spirit type degreaser, scissors or a construction knife, a marker, a stepladder.

Size: 1,5*15 mm.

Roll length: 35 m.

Application purpose:

• For sealing gaps
• To increase the fire resistance of fire gates, doors, smoke dampers, hatches, fireproof safes, etc

Characteristics:

• there is a self-adhesive layer;
• extension: 900%;
• the fire resistance limit is 240 minutes;
• service life: 25 years (subject to operating conditions).

Principle of operation

When the temperature rises to +150 °C and above, the fire-retardant material from which the tape is made swells, due to which the gaps between the fire door frame and the leaf are filled. This prevents smoke and fire from entering the adjacent room.

Exploitation:

• structures with fire-resistant tape are inspected at least once a year;
• during inspection, it is necessary to make sure that there are no unstuck sections of the tape, as well as mechanical damage to the tape;
• if there are peeled off areas, the surface must be degreased and glued with rubber glue;
• if there is mechanical damage, then it is necessary to remove the damaged area with a construction knife (with an overlap of 2-3 cm), and then stick a new tape without butt gaps.

Installation recommendations:

• installation is carried out at temperatures from -10 to +60 ° C;
• the installation site is pre-cleaned of dust and dirt, degreased;
• there should be no gaps at the joints of the pieces of tape;
• when gluing, the tape is tightly pressed against the surface; for reliability, the butt joints and the ends of the tape can be glued with rubber glue;
• the tape is installed without visible distortions and gaps; it may be necessary to use rags, a White Spirit type degreaser, scissors or a construction knife, a marker, a stepladder.

Size: 1,5*20 mm.

Roll length: 35 m.

Application purpose:

• For sealing gaps
• To increase the fire resistance of fire gates, doors, smoke dampers, hatches, fireproof safes, etc

Characteristics:

• there is a self-adhesive layer;
• extension: 900%;
• the fire resistance limit is 240 minutes;
• service life: 25 years (subject to operating conditions).

Principle of operation

When the temperature rises to +150 °C and above, the fire-retardant material from which the tape is made swells, due to which the gaps between the fire door frame and the leaf are filled. This prevents smoke and fire from entering the adjacent room.

Exploitation:

• structures with fire-resistant tape are inspected at least once a year;
• during inspection, it is necessary to make sure that there are no unstuck sections of the tape, as well as mechanical damage to the tape;
• if there are peeled off areas, the surface must be degreased and glued with rubber glue;
• if there is mechanical damage, then it is necessary to remove the damaged area with a construction knife (with an overlap of 2-3 cm), and then stick a new tape without butt gaps.

Installation recommendations:

• installation is carried out at temperatures from -10 to +60 ° C;
• the installation site is pre-cleaned of dust and dirt, degreased;
• there should be no gaps at the joints of the pieces of tape;
• when gluing, the tape is tightly pressed against the surface; for reliability, the butt joints and the ends of the tape can be glued with rubber glue;
• the tape is installed without visible distortions and gaps; it may be necessary to use rags, a White Spirit type degreaser, scissors or a construction knife, a marker, a stepladder.

Size: 2*10 mm.

Roll length: 25 m.

Application purpose:

• For sealing gaps
• To increase the fire resistance of fire gates, doors, smoke dampers, hatches, fireproof safes, etc

Characteristics:

• there is a self-adhesive layer;
• extension: 900%;
• the fire resistance limit is 240 minutes;
• service life: 25 years (subject to operating conditions).

Principle of operation

When the temperature rises to +150 °C and above, the fire-retardant material from which the tape is made swells, due to which the gaps between the fire door frame and the leaf are filled. This prevents smoke and fire from entering the adjacent room.

Exploitation:

• structures with fire-resistant tape are inspected at least once a year;
• during inspection, it is necessary to make sure that there are no unstuck sections of the tape, as well as mechanical damage to the tape;
• if there are peeled off areas, the surface must be degreased and glued with rubber glue;
• if there is mechanical damage, then it is necessary to remove the damaged area with a construction knife (with an overlap of 2-3 cm), and then stick a new tape without butt gaps.

Installation recommendations:

• installation is carried out at temperatures from -10 to +60 ° C;
• the installation site is pre-cleaned of dust and dirt, degreased;
• there should be no gaps at the joints of the pieces of tape;
• when gluing, the tape is tightly pressed against the surface; for reliability, the butt joints and the ends of the tape can be glued with rubber glue;
• the tape is installed without visible distortions and gaps; it may be necessary to use rags, a White Spirit type degreaser, scissors or a construction knife, a marker, a stepladder.

Size: 2*15 mm.

Roll length: 25 m.

Application purpose:

• For sealing gaps
• To increase the fire resistance of fire gates, doors, smoke dampers, hatches, fireproof safes, etc

Characteristics:

• there is a self-adhesive layer;
• extension: 900%;
• the fire resistance limit is 240 minutes;
• service life: 25 years (subject to operating conditions).

Principle of operation

When the temperature rises to +150 °C and above, the fire-retardant material from which the tape is made swells, due to which the gaps between the fire door frame and the leaf are filled. This prevents smoke and fire from entering the adjacent room.

Exploitation:

• structures with fire-resistant tape are inspected at least once a year;
• during inspection, it is necessary to make sure that there are no unstuck sections of the tape, as well as mechanical damage to the tape;
• if there are peeled off areas, the surface must be degreased and glued with rubber glue;
• if there is mechanical damage, then it is necessary to remove the damaged area with a construction knife (with an overlap of 2-3 cm), and then stick a new tape without butt gaps.

Installation recommendations:

• installation is carried out at temperatures from -10 to +60 ° C;
• the installation site is pre-cleaned of dust and dirt, degreased;
• there should be no gaps at the joints of the pieces of tape;
• when gluing, the tape is tightly pressed against the surface; for reliability, the butt joints and the ends of the tape can be glued with rubber glue;
• the tape is installed without visible distortions and gaps; it may be necessary to use rags, a White Spirit type degreaser, scissors or a construction knife, a marker, a stepladder.

Size: 2*20 mm.

Roll length: 25 m.

Application purpose:

• For sealing gaps
• To increase the fire resistance of fire gates, doors, smoke dampers, hatches, fireproof safes, etc

Characteristics:

• there is a self-adhesive layer;
• extension: 900%;
• the fire resistance limit is 240 minutes;
• service life: 25 years (subject to operating conditions).

Principle of operation

When the temperature rises to +150 °C and above, the fire-retardant material from which the tape is made swells, due to which the gaps between the fire door frame and the leaf are filled. This prevents smoke and fire from entering the adjacent room.

Exploitation:

• structures with fire-resistant tape are inspected at least once a year;
• during inspection, it is necessary to make sure that there are no unstuck sections of the tape, as well as mechanical damage to the tape;
• if there are peeled off areas, the surface must be degreased and glued with rubber glue;
• if there is mechanical damage, then it is necessary to remove the damaged area with a construction knife (with an overlap of 2-3 cm), and then stick a new tape without butt gaps.

Installation recommendations:

• installation is carried out at temperatures from -10 to +60 ° C;
• the installation site is pre-cleaned of dust and dirt, degreased;
• there should be no gaps at the joints of the pieces of tape;
• when gluing, the tape is tightly pressed against the surface; for reliability, the butt joints and the ends of the tape can be glued with rubber glue;
• the tape is installed without visible distortions and gaps; it may be necessary to use rags, a White Spirit type degreaser, scissors or a construction knife, a marker, a stepladder.

Size: 2*45 mm.

Roll length: 25 m.