Pipeline systems

Dimensions are presented in mm

Application purposes:

• For HL520-series

Material: PP

Weight: 0,039 kg

Space saver tubular trap HL 126.2/40 DN 40 horizontal is made of polypropylene. This device is designed so that it saves a lot of space under a sink, and trap is equipped with ball-joint outlet. Trap with connector DN40 x 1 1/2' for double sinks.

HL 134.0/40 concealed trap is embedded into the wall. HL 134.0/40 is made of polypropylene, it has diameter of 40 mm and capacity of 0.38 l/s. Trap insert can be removed if necessary.

Drip funnel HL 20 is used on air conditioners and manufactured by Hutterer Lechner. It can take water with jet break. Size of drip funnel is 170*92 mm. The drip funnel is made of polypropylene, its weight of 115 grams. With female thread 6/4". Also drip funnel is equipped with a pipe clip.

Documentation

Download data sheet: Drip funnel HL 20

Download example of product installation:  Drip funnel HL 20

Application area:

• For bath

Characteristics:

• Material: PP (visible parts chrome-plated)
• Size: DN40/50
• There is a device for filling
• Water can be connected both on the left and on the right
• Equipped with overflow
• Drain hole diameter is 60mm
• Exhaust type: swivel (allows it to rotate 280° horizontally and 10° vertically)
• There is a fitting that allows you to connect a drainage tube (size from 8 to 13 mm)
• The outlet is equipped with a double seal
• There is a Bowden cable (length 80 cm) - CrNi 18/10 steel is used for manufacturing

Capacity: 0.67 l/s.

Mounting at a height of 107 mm.

Product weight: 2,34 kg.

Documentation

Download example of product installation:  Waste and overflow assembly HL 560N.L

 *Diameter 80 gradually replace diameter 70

Dimensions are presented in mm

Application area:

• For air condition and ventilation

Characteristics:

• Material: ABS (PS)

Weight: 0,03 kg

Application area:

• For shower trays

Characteristics:

• Material: EPDM

Weight: 0,048 kg

Space saver tubular trap HL 126.2/50 DN 50 horizontal is made of polypropylene. This device is designed so that it saves a lot of space under a sink, and trap is equipped with ball-joint outlet. Trap with connector DN40 x 1 1/2' for double sinks.

HL 134.0/50 concealed trap is embedded into the wall. HL 134.0/50 is made of polypropylene, it has diameter of 50 mm and capacity of 0.38 l/s. Trap insert can be removed if necessary.

Application area:

• For bath

Characteristics:

• Material: PP
• Size: DN40
• Includes 6/4" swivel nut
• Acts as an extension

Weight: 0.080 kg.

ATTENTION! This product is temporarily unavailable for order!

Application purposes:

• For building drainage
• For buildings with increased sound insulation requirements

Characteristics:

• Abrasion resistant;
• Sound-absorbing;
• UV-resistant.

Material: PE-S2

Thermal expansion: 0.17 mm/(m*K)

Thermal conductivity, pipe: 0.43 W/(m*K)

According to DIN 1986, part 1, section 6.1.2, the changes of the direction of main pipelines and sewers may be fulfilled only with using prefabricated pipe bend, and each individual bend can have a maximum angle of 45^˚. In some cases, for these purposes can be used two pipe bends 45^˚. Due to the double knee one connecting element is saved and the installation becomes easier. In addition, this fitting provides a good opportunity to place the fastening element in its middle. The bend is also intended for use as a transition from the riser to a horizontal pipe, and vice versa.

*Diameter 80 gradually replace diameter 70